With the development of the economy, cars have become a common mode of transportation. Urban parking lots allow cars in cities to run smoothly and smoothly. Parking lots are becoming an indispensable component of a city, and its illumination should also be taken seriously. Targeted lighting in the parking lot is not only a requirement to ensure the use, but also a need to ensure the safety of property and people.

The technology and systems of our parking lights are continuously improved. With the rapid development of China’s economy, the urban population has soared, and the number of motor vehicles has increased rapidly. More and more urban parking lots have been developed in underground garages. Parking lot energy consumption is a major component of the operating cost of underground parking lots.

At present, most of the underground garage lighting mainly uses energy-saving lamps and zone control to reduce energy consumption, but it also brings some inconvenience to the owner during the use process. Only a few underground garage lighting use intelligent lighting control systems, which have functions such as area control and timing control, but this system has a series of problems such as high cost, complicated operation, and certain incompatibilities in matching with the security system. Facing the energy consumption of underground garage lighting and the safety lighting requirements of owners, how to achieve energy-saving lighting and provide humanized services is one of the problems faced by many companies that manage parking lots. Our company’s products are specially developed for outdoor parking lots / indoor underground parking lots.

 

Our parking lot lighting features

1. Independent research and development of high-efficiency light sources;
2. The light emitting device has high luminous efficiency and its performance surpasses similar domestic products;
3. Adopting advanced power supply circuit design, the heat of the lamp body is small;
4. Advanced manufacturing technology, super long life design.
5. Good color rendering: it can be closer to daylight than the light emitted by traditional lamps;
6. It is not limited by the startup temperature, it can be started transiently, usually a few ms, and it can reach the full luminous flux output transiently;
7. Long life. The actual life of LED is more than 20,000-80,000 hours, which is several times or even dozens of times of the general light source.

 

Underground parking lot lights

LED fluorescent lamp, using LED light source and full built-in radar sensor control technology, can fully provide sufficient lighting for car owners to drive in and out of underground garages quickly and safely. And when there is no vehicle entering or exiting, it will automatically switch to the power-saving lighting state to provide certain lighting for monitoring. The long-term power consumption is only equivalent to 10% of the electricity consumption of traditional lighting, and the energy saving effect of underground garage lighting is more than 90%, thereby achieving the effect of “lights on and also saves power”.

1. Energy-saving lighting for parking garage

LED parking lot lamps: For the long time and large power consumption of underground parking lots, our company has developed a dedicated underground parking lot lamp through repeated experiments and tests, combining various factors, with a built-in intelligent control system. In order to achieve the best energy-saving effect, the car comes on, the car goes off, and the on-demand lighting is truly realized. Our underground parking lot LED special light, which integrates infrared and microwave automatic induction system and intelligent control system, can set its working mode in advance according to the use environment, and the lighting system will automatically work in a preset mode.

2. Motion-sensing lights

This system can realize on-demand lighting, which can greatly reduce power consumption under the premise of ensuring normal lighting. When a person or a car enters the parking lot, the person or car enters a certain induction control area, and the lamps in the corresponding area automatically switch to a preset working state. When the person or car leaves a certain induction area, the lamp uses a predetermined delay time. Automatic adjustment to low-light state (power consumption 2 watts), to achieve “people come to light, people go to dim, lighting on demand”, under the premise of ensuring normal use, completely change the situation, to eliminate most of the ” “Invalid lighting” phenomenon, and can ensure the normal operation of the security monitoring system to supplement the light needs, the use of this product is a qualitative leap in the energy saving of parking lot and building public places lighting, more importantly, establish and promote a New concept: “On-demand lighting” concept. A single lamp can realize intelligent control, or it can be connected to the intelligent control system of Guoguang Green Energy, which can control and control the operation status of the parking lot lighting system at any time in the monitoring center; built-in open communication protocol can be compatible with all existing controls system.

The underground parking lot is an uninterrupted lighting occasion all year round. Most of the time, there is no car or unmanned state, so the power is wasted and the light source loss rate is high. At present, sensors used in parking lot lighting are basically divided into two types. One is an infrared sensor, which has a lower price. However, due to the limitation of the height of the infrared sensor, the metal pipeline and the radiation angle have a certain detection blind zone. The other is a microwave sensor, which can overcome the shortcomings of the blind area of ​​the detection angle, but the price is slightly higher. The two sensors are combined with the LED lights, which can effectively realize the energy saving of the underground parking lot. When someone has a car moving around the lamp, the LED lighting lamp runs at full rate to meet the needs of lighting. When no one is without the car, the light is in a dormant state, maintaining a low power of about 3W, and maintaining the required power for safe lighting. The lowest illuminance achieves lighting power saving, and its power saving rate can reach more than 80%.

3. Modular design for easier maintenance

The LED lights of the parking lot must be combined with the control in order to take advantage of the characteristics of the LED light source. The power supply control module and the LED light source module must be connected by a connector to facilitate maintenance and replacement. The appearance of the luminaire should be innovative. It should not be the same as the traditional light source. LED luminaires must have artistic shapes. Because they are in a low brightness state for a long time, no heat treatment is generally required. To reduce material consumption, material saving is also part of energy saving.

 

Outdoor parking lights

Outdoor parking lot lighting quality requirements:

• Illuminance requirement
• Uniformity of the illuminance
• Color rendering of the light source
• Color temperature requirement
• Glare is also an important indicator to measure.

High-quality venue lighting can create a relaxing and good visual environment for drivers and pedestrians. Reasonable lighting design is very important to improve the uniformity of illumination, three-dimensional sense, reduce glare, and meet lighting requirements. Different lighting methods in parking lots produce completely different lighting effects. At present, many domestic parking lots use high-pole or semi-high-pole lights to illuminate, and there are few lamps. The prominent problem of this type of parking lot is that the uniformity of lighting in the entire parking lot is poor, and when there are more vehicles parked, it will form Obscures shadows and makes them uneven. In contrast to this is the case of using ordinary street light poles, with many lamps (relative to the former). The investigation found that this type of lamp arrangement has a reasonable distribution of lamps and a targeted consideration of the choice of lamps. When the same illumination as the former is achieved, the latter has a significantly better uniformity of illumination. Such a venue is more convenient to use. People reflect better. Therefore, based on the above analysis of the current situation and the layout characteristics of this parking lot, the design of this parking lot uses single-headed street lamps with low height and half-cut light fixtures, which are arranged in rows at the boundary of the site. , While reducing the light interference caused by parking lots to surrounding roads and buildings.

Specific luminaire layout: the installation height of the luminaire is 8 meters, the street lamp poles are installed on the ground, and the two sides of the parking space are symmetrically arranged on both sides (the road width is 14 meters) with a distance of 25 meters. The installed power of the lamp is 126W. Properly narrow the distance between the lamps at the entrance and exit to increase the level of illumination.

1. Entrances and exits

The entrances and exits of the parking lot need to check the certification, toll, and identify the driver’s face, to facilitate communication between the staff and the driver; railings, facilities on both sides of the entrance and the entrance, and the ground must provide corresponding lighting to ensure the driver Drive safely, so lighting here should be appropriately enhanced and targeted lighting provided for these operations. GB 50582-2010 stipulates that the illumination at the entrance of the parking lot and the toll booth should not be lower than 50lx

2. Signs and markings

The signs in the parking lot need to be irradiated to be seen, so the lighting of the signs should be taken into account when designing the lighting. Then there are the markings on the ground. When setting the lighting, you should ensure that all the markings can be clearly displayed.

3. Car body parking space

For the illumination requirements at the parking space, ensure that the ground markings, ground car locks and isolation railings are clearly displayed to ensure that the driver will not hit the ground obstacle due to insufficient illumination when entering the parking space.  After the vehicle is parked in place, the body should be displayed through appropriate lighting to facilitate the identification of other drivers and the access of the vehicle.

4. Pedestrian route

Pedestrians will have a section of walking road when they pick up or get off the vehicle. This section of the road should be considered as an ordinary pedestrian road to provide lighting and provide appropriate ground lighting and vertical surface lighting. There may be a mixed use of the pedestrian route and the roadway in this parking lot, which should be considered according to the standard of the roadway.

5. Environmental interference

For the sake of safety and identification, the environment of the parking lot should be illuminated. However, the impact on the off-site environment atmosphere should be reduced. After all, the vehicle or parking lot is not a beautiful decoration in the public environment. They may destroy the original harmony of the environment. The above problems can be improved by arranging the lamps. An array of continuous light poles is formed around the parking lot, which can act as a line of sight barrier and achieve an isolation effect inside and outside the parking lot.

LED is a solid-state light source. It has the characteristics of small size, fast response, modular combination, power can be adjusted at will, and DC power supply, which brings great convenience to the manufacture of lamps.

Commonly used conventional street light lighting methods, using single-head or top-mounted LED street lights on street light poles, the height of the street light poles is 6 meters to 8 meters, the installation distance is about 20 meters to 25 meters, and the power of LED street lights is 60W-120W. Wide maintenance range The height of the pole light adopts: 20m-25m; the number of LED flood lights, 10-15 sets; the power of LED flood lights: 200w to 300watt.

 

Underground parking lot lights

Radar induction LED fluorescent lamp (Main product)

The radar induction LED fluorescent lamp is mainly an all-round no dead angle induction. As long as an object reaches the sensing range, the lamp will light up for itself, the length of time the light is on, and the induction distance can be adjusted. It can be based on the actual needs of customers. determine. Radar sensor LED fluorescent lamp is the best choice for underground parking lot. Although the current price is a little higher than ordinary fluorescent tubes, but radar sensor LED fluorescent lamp is more power-saving, and in the long term cost, radar sensor LED fluorescent lamp is the most cost-effective choice.